Outboard decal Replicas - Find them here!

Outboard Decals

60R EFI 4STROKE RACING - Cat.# 90-8M0169885

 > Mercury Marine [Updated: Sep. 3, 2020] > Outboard > 4 Stroke > 60R EFI FourStroke Racing > [1C615064 & Up] - Cat.# 90-8M0169885

 

TOP COWL DIAGRAM 70940

8M0118165 TOP COWL ASSEMBLY Mercury, Non Decaled

MERCURY DECALS

8M0171547 DECAL SET Top Cowl
8M0080154 DECAL M-ICON, Blue Front
8M0151525 DECAL MICON 53 MM, Racing Rear
8M0056643 DECAL Read Manual Rear
8M0159886 DECAL Lenz, Mercury

8M0171547, 8M0080154, 8M0151525, 8M0056643 DECAL, 8M0159886,
8M0171547 8M0080154 8M0151525 8M0056643 DECAL 8M0159886

 

35 ELO - Cat.# 90-43116

> Mercury Marine [Updated: Feb. 18, 2023] > Outboard > 2 Stroke Carb > 35 (2 CYL.) > [209608 & Up] - Canada - Cat.# 90-43116
> Mercury Marine [Updated: Aug. 18, 2020] > Outboard > 2 Stroke Carb > 35 (2 CYL.) > [6445653 THRU 0B110788] - USA - Cat.# 90-43116




TOP COWL DIAGRAM  38716

6341 TOP COWL ASSEMBLY (ELECTRIC)

6341, 6340A2

MERCURY DECALS

43206A84 DECAL SET (BROWN)
+13481A89 DECAL SET

13481A86 DECAL SET (SILVER)
+13481A89 DECAL SET 







 

 

Subcategories

  • Mercury-Mariner-Tracker-Force Outboard Decals

    DECAL DRY APPLICATION

    IMPORTANT: This document guides our dealers, boatbuilders, and company service personnel in the proper installation or service of our products. If you have not been trained in the recommended servicing or installation procedures for these or similar Mercury Marine products, have the work performed by an authorized Mercury Marine dealer technician. Improper installation or servicing of the Mercury product could result in damage to the product or personal injury to those installing or operating the product.
    NOTE:After completing installation, place these instructions with the product for the owner's future use.
    IMPORTANT: This decal set must be applied dry. Do not use a soap and water mixture to apply this decal set.

    Tools, Materials, and Surface Requirements

    Tools and Materials

    • Decal application squeegee (3M® Applicator PA 1 Gold - recommended)
    • Air release tool (3M Air Release Tool 391x) or a straight pin - used to remove trapped air bubbles
    • Clean microfiber towel (Meguiar’s® Supreme Shine Microfiber Towel - recommended)
    • Spray bottles and labels for each cleaning solution
    • Cleaning solution:
      a. Liquid dishwashing soap
      b. Isopropyl alcohol
      IMPORTANT: Identify each spray bottle of cleaning solution with a label.

    Surface Requirements

    Special attention is required when applying decals to certain surfaces, including primed, painted, and certain plastics. All
    painted surfaces must be cured per the manufacturer's requirements. When applying decals to plastic surfaces, allow proper
    time for out gassing.

    Surface Preparation

    Application Temperature

    Apply the decal when the surface and ambient air temperature is between 16-373 °C (61-99 °F).
    NOTE: Applying the decal near the minimum temperature specification, the adhesive bond will develop more slowly than temperature in the mid to upper specification range.

    Step One General Cleaning

    IMPORTANT: Do not shortcut the cleaning process. All of the surfaces are considered contaminated prior to a thorough
    surface cleaning preparation.

    1. Mix a solution of 29.5 cc (1 fl oz) liquid dishwashing detergent with 3.7 Liter (4 US qt) of warm water.
    2. Rinse cowl with clean water.
    3. Dry the cowl with a clean Meguiar‘s Supreme Shine Microfiber Towel.
    4. Avoid detergents or preparations that contain waxes, oils, or lotions.

    Step Two Solvent Cleaning

    1. Mix a solution of isoprooyl alcohol and water to a 1:1 ratio. Store in a spray bottle and identify the solution with a label.
    2. Saturate a clean paper towel with the isopropyl alcohol and water solution.
    3. Wipe the cowl with the saturated towel followed immediately with a lint-free towel before the solution evaporates.
    NOTE: Isopropyl a/coho/ evaporates quickly. You must Wipe the surface immediately after applying the solution.
    4. When the paper towel becomes contaminated with dirt, discard it and use a clean paper towel saturated with the
    isopropyl alcohol and water solution.
    5. Ensure the surface has no contamination and is completely dry.
    6. Start to apply the decals immediately after solvent cleaning.

    Decal Application

    Application Tips

    1. Ensure that the surrounding work area and the surface are properly cleaned to avoid contamination.

    90-8M0143239 eng MARCH 2018       © 2018 Mercury Marine      -     Page 1 / 16

  • Evinrude-Johnson Outboard Decals
  • Nissan-Tohatsu Outboard Decals
  • Yamaha Outboard Decals
  • Suzuki Outboard Decals
  • Honda Outboards